Verifiable specifications
Product information supported by official records
| Build volume | 350 × 350 × 350 mm | View source |
|---|---|---|
| Hotend temperature limit | 350 °C | View source |
| Bed temperature limit | 120 °C | View source |
| Active chamber heating | 65 °C | View source |
| First-generation ACE Pro support | First-generation ACE Pro is not supported | View source |
| Printer dimensions | 502.7 × 483 × 584 mm | View source |
Three heating figures answer three questions
The hotend limit is 350 °C, the heated-bed limit 120 °C and the active chamber figure 65 °C. Do not exchange these values or treat them as recommended settings for every filament. Match the documented material profile to the exact printer and feed arrangement before deciding whether the configuration suits the intended job.
Anycubic Kobra S1 Max has the following documented hotend temperature limit: 350 °C. A hotend temperature ceiling is an operating limit, not a complete material-compatibility list or the setting for every print. Read it alongside this model’s documented filament guidance, nozzle configuration and print profiles. The maximum alone does not establish that an enclosure-dependent, abrasive or otherwise restricted material has been approved for this configuration.
Anycubic Kobra S1 Max has the following documented bed temperature limit: 120 °C. The same configuration lists hotend temperature limit as 350 °C. Treat the bed limit separately from the hotend limit and the installed print surface. Those entries answer different questions, so a higher nozzle maximum does not automatically give the bed or surface the same capability. Use the documented material and surface combination when selecting a print profile rather than treating the maximum as a universal adhesion setting.
Anycubic Kobra S1 Max has the following documented active chamber heating: 65 °C. The same configuration lists hotend temperature limit as 350 °C. Keep the chamber claim separate from nozzle and bed temperatures. An enclosure, an actively heated chamber and an “up to” chamber-temperature statement are not interchangeable descriptions. For the configuration documented here, check the material guidance and any stated conditions; the chamber entry alone is not evidence that every job reaches the listed maximum.
Allow for the machine, not only the large print
The listed machine size is 502.7 × 483 × 584 mm. Compare that with the location and consult installation instructions for access, then check the intended part in the 350 mm cube profile. Resolve the original ACE Pro exclusion before purchase; the large envelope does not change the connection boundary.
Anycubic Kobra S1 Max has the following documented build volume: 350 × 350 × 350 mm. The same configuration lists printer dimensions as 502.7 × 483 × 584 mm. A usable build volume sets the boundary for the object you plan to print. Compare the part in its intended orientation with this envelope before choosing the machine. This measurement is different from the printer’s outside dimensions: fitting the printer on a desk does not establish that a particular part fits inside it.
Anycubic Kobra S1 Max has the following documented first-generation ace pro support: First-generation ACE Pro is not supported. Separate the printer’s material route from the optional feeder’s route. For the documented arrangement, check which unit is required, which combinations are allowed and any excluded materials before buying an expansion package. A channel or color-capacity statement describes a configuration; it does not by itself establish that a different generation’s hardware, cable or hub can be substituted.
Anycubic Kobra S1 Max has the following documented printer dimensions: 502.7 × 483 × 584 mm. The same configuration lists build volume as 350 × 350 × 350 mm. Use the documented dimensions to plan the physical installation, retaining the exact configuration and measurement conditions. Allowing for the stated machine outline is a starting point; confirm access for the documented loading, removal and maintenance tasks before committing to a tightly fitted location.
Exact product identity
Product identifiers in official records
GTINs, UPCs, manufacturer SKUs and model codes can identify different colors, configurations or bundles. Only identifiers stated in official records are shown; an unpublished ASIN is not inferred.
| Identifier | Exact value | Variant or bundle | Market | Source and review |
|---|---|---|---|---|
| Manufacturer product name | Kobra S1 Max | Model level | United States | Anycubic · store.anycubic.comAnycubic Kobra S1 Max — Model identity · |